|
FAQ You can get answers to the most frequently asked questions. |
CIRCUIT DESIGN,INC. |
|
|
||||||||||||
| Products Search FAQ by products | ||||||||||||
| Topics Search FAQ by topics | ||||||||||||
|
||||||||||||
Your search (in Topics: Others) resulted in 28 hits.
| Products | Topics | Questions |
| None | -Others | Is there any problem if the module has condensation? |
| None | -Others | What is 12dB SINAD |
| None | -Others | Can images from a camera be transmitted? |
| -MU-1-R | -Others | Can you check the content of communication between two MU-1 units using a ghird unit? |
| -MU-1-R | -Others | Can you connect the MU-1 with RS-485? |
| -MU-1-R | -Others | Can the MU1-UIK be used with Windows CE? Also, can it be used with the windows Mobile 2003 O/S? |
| -MU-1-R | -Others | There is no change in RTS output. It is always Low. Is this OK? |
| -MU-1-R | -Others | When the MU-1 is in the receive mode, is the data output from the DO terminal only valid data? Also, when the receiver is not receiving an RF signal, what does DO output? |
| -MU-1-R | -Others | Every tiem "Open port" in the MU1-ESP is clicked, "Framing error" is displayed. |
| -MU-1-R | -Others | Can models without the relay function be built into networks with the relay function? |
| -CDP-TX-02E-R/CDP-RX-02E-R | -Others | What are differences between CDP-TX/RX-02N and CDP-TX/RX-02E-R? |
| -CDP-TX-04S-R/CDP-RX-03AS-R | -Others | Is it possible to use the CDP-TX-04S with the CDP-RX-03AS/BS-R? (or the CDP-TX-04S-R with the CDP-RX-03AS/BS) |
| -CDP-TX-02E-R/CDP-RX-02E-R -CDP-TX-02EP-R/CDP-RX-02EP-R -CDP-TX-02F-R/CDP-RX-02F-R -CDP-TX-02FP-R/CDP-RX-02FP-R | -Others | What are differences between CDP-TX/RX-02E-R and CDP-TX/RX-02F-R? |
| -MU-1-R | -Others | Is there a way to put the MU-1-R into standby mode? |
| -WA-TX-01-R/WA-RX-01-R -WA-TX-03-R/WA-RX-03R | -Others | Is Fullduplex communication possible between the WA-TX-01-R (WA-TX-03-R) and WA-RX-01-R (WA-RX-03-R)? |
| -MU-1-R | -Interface -Others | Is it possible to send graphics data from an MU-1-R connected to a digital camera? |
| -WA-TX-03-R/WA-RX-03R | -Others | I want to know about the operation of the standby terminal of the WA-TX-03-R. |
| -CDP-TX-02E-R/CDP-RX-02E-R -CDP-TX-02EP-R/CDP-RX-02EP-R -CDP-TX-02F-R/CDP-RX-02F-R -CDP-TX-02FP-R/CDP-RX-02FP-R | -Others | What are the frequencies of any intermediate frequency (IF) stages in the CDP-RX-02E-R (CDP-RX-02EP-R, CDP-RX-02F-R, CDP-RX-02FP-R)? |
| -MU-2-R | -Others | How can the RSSI value be obtained when the MU-2-R is inbinary mode? |
| -WA-TX-01-R/WA-RX-01-R | -Others | How long do the WA-TX-01 and WA-RX-01 take to start up? |
| -CDT-TX-01/CDT-RX-01 | -Others | What are the important points to remember for two-way communication between the CDT-TX-01 and CDT-RX-01? |
| -WA-TX-03-R/WA-RX-03R | -Others | How many channels are usable with the WA-TX/RX-03-R at one time? |
| -WA-TX-03-R/WA-RX-03R | -Others | Is it possible to see the RSSI output level of the WA-RX-03-R? |
| -CDT-TX-01/CDT-RX-01 | -Others | How long does it take to start transmission after switching on the CDT? |
| -WA-TX-03-R/WA-RX-03R | -Others | What are the important oint to remember when a WA-03 module is operated on a test board which enables the frequency and mute level to be changed? |
| -CDT-TX-01/CDT-RX-01 | -Others | I'm using two CDT-TX-01 units and one CDT-RX-01A. Why is there a delay of 15 seconds between transmission from the first transmitter and the second transmitter? |
| -MU-2-R | -Others | How many times is the MU-2-R samples when the RSSI level is measured? How long does it take to measure the RSSI level? |
| None | -Propagation of radio -Others | What is multipath fading? What is a dead spot? |